所谓RC电路的零状态,是指换路前电容元件未储有能量,。在此条件下,由电源激励所产生的电路的响应,称为零状态响应。 电容元件两端的电压 可将计算线性电路暂态过程的步骤归纳如下:(1)按照换路后的电路列...
2023-07-21 176 电容 电源
&nbs...
2023-07-21 218 三极管 电容 电源
在放大电路中,电容C1、C2起交流耦合和隔直作用,根据阻抗特性,电容C1、C2对直流信号认为是开路,而电容C1、C2和直流电源Vcc对交流信号则可以认为是短路的,所以在交流通路中Rb和Rc都是连接到地...
2023-07-21 208 电容 电源 三极管
上图所示基本共射放大电路的偏置电流IB由Vcc和Rb决定,电路参数一经选定,偏置电流就固定不变,所以称为固偏电路。作为半导体器件,三极管的特性受温度的影响很大,当温度升高时,同样的偏置电流所对应的集...
2023-07-21 234 三极管 电源 电容
单个放大电路的放大倍数有限,因此往往需要两级以上放大电路串联起来使用。在多级放大电路中,每两个单级放大电路之间的连接方式称为耦合,分为以下三种:1、阻容耦合:两级之间通过耦合电容及后级输入电阻连接。由...
2023-07-21 237 电容 集成电路
三极管基本放大电路是放大电路中最基本的结构,是构成复杂放大电路的基本单元。它利用双极型半导体三极管输入电流控制输出电流的特性,或场效应半导体三极管输入电压控制输出电流的特性,实现信号的放大。本章基本...
2023-07-21 173 三极管 电子 电源 电容
任何电路选择电容器时都需要注意失真问题。如果电容器在信号路径中,就会出现这类失真。图1是2个在信号路径中包含电容器的典型电路。 图1a是Sallen-Key带通滤波器的第一级。在该电路中,两个重要电...
2023-07-21 214 电容 电容器
在PWM和电子镇流器当中,半桥电路发挥着重要的作用。半桥电路由两个功率开关器件组成,它们以图腾柱的形式连接在一起,并进行输出,提供方波信号。本篇文章将为大家介绍半桥电路的工作原理,以及半桥电路当...
2023-07-21 251 电子 电源 电路图 电容
图1为某仪器按键电路原理图,按键安装在仪器面板上,通过导线连接到主控板上,按键的一端接上拉电阻并连接后续电路,按键的另一端接地,当按键没有按下时,按键输出高电平,当按键按下时,按键输出低电平。图...
2023-07-21 234 接地 电容 电源
读放大电路图时也还是按照“逐级分解、抓住关键、细致分析、全面综合”的原则和步骤进行。首先把整个放大电路按输入、输出逐级分开,然后逐级抓住关键进行分析弄通原理。放大电路有它本...
2023-07-21 204 电路图 电容 三极管 接地